Mossberg 500 plug removal

The Maverick 88 pump-action shotgun has a magazine capacity of six to eight shells, depending on the model. This firearm comes with a factory installed "magazine capacity reduction plug. The two-shell limit conforms to hunting laws in many states where it is illegal to have a shotgun capacity greater than three one in the chamber, two in the magazine.

If your Maverick 88 does not have the plug, don't worry. It's easy to install. Loosen the take down screw assembly. Open the action on your shotgun halfway, then fully loosen the take down screw at the front of the magazine.

This screw protrudes from the bottom of the barrel. It both caps the end of the magazine and connects the barrel to the magazine tube. Remove the barrel.

The entire shotgun barrel will slide forward easily, opening the end of the magazine tube. Mount the rubber washers onto the dowel. The washers should be near each end of the rod. They are not essential, but they will keep your dowel from rattling around in the magazine tube. The length of your dowel rod depends on the length of your magazine tube, but it should leave at least six inches of space within the magazine to accommodate two 3-inch shells.

Place the dowel in the magazine tube. Slide the wooden dowel, with washers snuggly attached, into the open end of the tube. Replace the barrel and tighten the take down screw. Carefully slide the barrel back into place.

Firmly tighten the screw, sealing the magazine tube and attaching the barrel to the rest of the firearm. Jacob Buckenmeyer began writing professionally in About the Author. Photo Credits.Posted: Mon Feb 02, pm.

Only 3 shells can be loaded, I know that thats whats needed for hunting but I dont hunt THX Dan. I'm not sure if all Mossberg s are the same. The plug on mine is quite simple, funny Ok jokes aside. The plug on mine is literally a wooden dowel with 2 O-rings on it. To remove it, take the barrel off the gun.

Then hold the gun vertically with the butt on the top. Look at end of the magazine tube and you should see the plug start coming out.

How to Remove the Plug From My Mossberg Model 500

Pull it out and you've increased the capacity of the gun. Mind you, this may not be legal in your state. Posted: Tue Feb 03, am. If your state has a law limiting magazine capacity for shotguns to a certain number, then simply having a plug in a magazine that's over the limit won't make the gun legal, since it's not a permanent modification.

So if the gun was legal in the first place, taking out the plug won't make the gun illegal. Posted: Tue Feb 03, pm. Arkalius, Here in NJ, I believe it is illegal to put more than 3 rounds in a shotgun. By pulling out the plug, that makes it illegal.

Usually, the plug makes it legal to hunt with the shotgun waterfowl, etc. Taking the plug out means that if you're out in a duck blind with five shells in the magazine, you're liable for a game laws citation. Legal to own is a different issue. It looks from the NRA-ILA link that you can't have a "semi-automatic shotgun with a magazine capacity of more than six rounds.

Most manufacturers will send you a new one free or for a nominal cost. Posted: Thu Feb 05, pm. Posted: Fri Feb 06, am. Would there be any models that have a 'permanent' plug? I live in California so that may be an issue In California you're fine up to 10 rounds, so don't worry about it. The primary purpose of the plug is to comply with game regulations that require your gun be able to hold no more than 3 rounds.

When I said that the gun is legal, I mean to own. Taking out the plug will make hunting certain game with it illegal. Posted: Sat Feb 07, am. Sorry to go off topic, but can someone please tell me the length and diameter of the dowel rod used to plug the magazine on the ?

My puppy chewed mine up the first day I owned my gun and I have not replaced it yet.Posted: Mon Jan 03, am.

Shotgunworld.com

I have a brand new bore Mossberg mini shotgun. I removed the long wooden dowel inside the magazine chamber. Any advice? Posted: Mon Jan 03, pm. Three is all she'll hold. Which is one more than you can hunt with anyway. Posted: Tue Jan 04, am. Natman, thank you for the very quick replies.

I knew this "mini" was too good to be true. I guess three is all she'll hold. Posted: Thu Jan 13, pm. I am pretty sure they were going for a small, light-weight shotgun that could be easily wielded by younger children when they start hunting. To us it might not make a huge difference, but a full-length mag tube loaded with another few ounces of shells might have completely offset the feel they were going for. That said, I soooo wish they would or would have put out a mini with a full-length mag tube on the My GF loevs her Page 1 of 1.

Previous topic Next topic. Author Message joeyant. Utility Grade. Limited Edition. Presentation Grade. You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum. Matarese Jr.The Mossberg model shotgun is favored among many shooters and hunters for its durable construction and affordable price.

Featuring a pump action, the Mossberg model is available in both gauge and gauge, with chokes that include improved, full and modified. Due to game regulations in many states, a plug or dowel is inserted into the magazine tube to limit the rounds carried to two plus one in the chamber. You can remove the plug from your Mossberg with relative ease.

Unload the Mossberg modelmaking sure there are no shotgun shells in the magazine tube or in the firing chamber. Visually inspect the shotgun to make sure that it is unloaded. Locate the magazine cap on the end of the short-shell magazine under the barrel of the shotgun.

GIRL HIP FIRING the PISTOL GRIP MOSSBERG 500 for the FIRST TIME!! GIRLS SHOOTING GUNS!!

Loosen and remove the magazine cap by turning it counterclockwise. Pull the barrel from the receiver and guide the barrel mounting ring from the end of the shell magazine tube. Place the barrel to the side. Point the shotgun down and shake slightly to move the plug, or dowel, toward the end of the magazine tube. Pull the plug or dowel from the tube with your fingers or a pair of needle-nose pliers. Pull the plug or dowel past the rubber ring at the end of the magazine tube and out.

Slide the barrel mounting ring back onto the magazine tube and guide the end of the barrel into the receiver. Place the cap back onto the magazine tube to secure the barrel in place. Keith Dooley has a degree in outdoor education and sports management. He has worked as an assistant athletic director, head coach and assistant coach in various sports including football, softball and golf. Dooley has worked for various websites in the past, contributing instructional articles on a wide variety of topics.

Items you will need Rag Needle-nose pliers. About the Author.After over 50 years and over 10 million and counting—and the only pump action to be declared MilSpec—the Mossberg has proven to be one of the most versatile and reliable shotgun platforms available, offering a model to fit every application, and every user from our households, to law agencies, to military worldwide.

Customers - Should your firearm or any component of your firearm require service, kindly ship the entire firearm not just components to our Product Service Center postage paid, via your chosen carrier. We do not accept C. Vortex Canada Phone E-mail : info vortexcanada. Owner's Manuals are available online. We use cookies to help provide you with the best possible online experience. By using this site, you agree that we may store and access cookies on your device.

Read our Privacy Policy to learn more about how we use cookies. Search for:. Built Rugged. Proudly American. A statement that truly sums up the The most prolific and reliable shotgun in the world is also the most versatile shotgun platform available, with a model to fit every season, every application, and every user. Built rugged for military, police, and law abiding citizens, the mossberg tactical line offers mission-ready shotguns for any scenario.

Models New for Hello, I'm Thomas Lynch with O. I'm a Senior Engineer here at Mossberg. Today, I'm going talk to you about how to….

mossberg 500 plug removal

Turkey hunting and bad weather, metaphorically, do not go together to the casual observer. However, I can promise you that when bad weather rolls in,…. Struggling to find that perfect last-minute Valentine's Day gift? Check out this list of firearms gift ideas for the gun enthusiast in your life.Brand New Mossberg issue. Hey guys, hoping I could get some help here.

mossberg 500 plug removal

I bought a brand new and have not shot it yet. I was handling it yesterday when I noticed a sliding noice coming from the gun. I point it to the ground and you woul hear something sliding around. Turns out it was the Magizine Plug. I hope I got the name right because I don't have the book on me. This slide out the hole on the end of the Magizine tub eventually.

My question is, how important is this piece and did it need to come out. Do I need to have someone put it back in?

Hope I explained this right. Re: Brand New Mossberg issue. Often refered to as the duck plug. It limits the gun to only holding 2 rounds in the magazine and one in the chamber 3 total Generally Mossbergs have a couple of black rubber O-rings on this plug.

How to Disassemble a Mossberg 500 Series Shotgun

If you intend on hunting ducks then you need it. Just drop it back in the hole and with a bit of shaking it will go back in all the way. Make sure you check you local laws. Here in North Dakota you are required to have it for all upland game, including ducks. I found out the hard way hunting pheasants last year. Minnesota only requires it for waterfowl. I have one and the plug is NOT suppose to be sliding around.

Either you are missing the tube cap,your spring is not in correctly. You order a new plug or cut one yourself from a larger wooden dowel that you can get anywhere.

How to Plug a Maverick 88

Nothing should be sliding around. If you have the manual look at the diagram.

mossberg 500 plug removal

It will show you the correct plug assembly. If you don't have a manual down load one or call Mossberg.Posted: Sun May 10, am. How does one go about removing the magazine tube spring from a Mossberg ? Posted: Sun May 10, pm. You need to unscrew the magazine tube.

You'll need a high temp. They loctited them in on the newer models. You can use a strap wrench way out on the forward end after heating, if necessary. Posted: Mon May 11, am.

I don't think he wants to remove the magazine. Only the magazine spring. You have to remove the magazine end plug. I use a small screw driver and pry it off. It's a PITB. Then you can remove the spring. Be careful.

mossberg 500 plug removal

The spring is under tension and comes flying out if you don't hold it. Herb S. I wish you a lot of luck getting the front of the mag. Well, I have the synthetic and it has to be pried off. A friend has a Chinese made Norinko sp. A replica of the Rem and it has a plug that you push in, give it a quarter turn and it pops right out.

Very handy. Anyway, you have to remove the plug to get the spring out. Posted: Wed May 13, am. Unfortunately Herb, the front of a mag tube isn't made like a or I have all three and I wish they were. Neanderthal is right. You have to heat the tube were it screws into the receiver and use either a strap wrench or a padded pair of vice grips to remove it.

Also, be sure and grab it at the top. If you grab it in the middle or at the receiver you may crush the tube, or at least mash it in enough that the follower can't move. You mean you have to remove the mag. Hard to believe. How do you remove the plug? I had a once and don't remember taking the tube off to clean it. I downloaded the owners manual for the and here is the part that explains it.

Posted: Wed May 13, pm.


This entry was posted in Mossberg 500 plug removal. Bookmark the permalink.

Responses to Mossberg 500 plug removal

Leave a Reply

Your email address will not be published. Required fields are marked *